爆炸地震波评价地面毁伤效应的实验研究

通过实验探索爆炸地震波评价爆源对地面冲击波毁伤效应的可能性 ,结果表明 ,在相同的地层状态条件下和一定的距离范围内 ,用爆炸地震波评价爆源对地面的毁伤效应是可行的。这在很大程度上弥补了利用空气冲击波压力测试和模拟目标毁伤评价燃料空气炸药 (FAE)爆源爆炸空气冲击波威力的不足。     

微孔洞型的分形断裂理论初探

初步研究并提出微孔洞型的分形断裂理论，建立了主裂纹与微孔洞汇合的分形模型，并以此为基础确定了分维Ｄ与连接区厚度Δ和孔洞平均半径ｒ之间的关系，推导了微孔洞与主裂纹连接的能量准则，讨论了分维与断裂韧性之间的关系。     

T300/648迭层板接头挤压疲劳损伤参数的选择与测定

本文对碳纤维增强复合材料迭层板(C.F.R.P)接头在不同环境条件下的挤压疲劳损伤扩展进行了实验研究.并根据“剩余强度,剩余刚度”理论和“疲劳模量”概念,讨论了接头的刚度下降和强度变化.由此提出了“损伤参数”D的定义和测量方法;并对损伤试件,进行了X射线检测分析,验证了累积损伤的扩展.     

力学可以为农业现代化作贡献

农业现代化提出了许多与力学各个分支都有密切关系的问题．从农田耕作、农业物料性质、农产品烘干、水果和蔬菜生产、农业生物环境、节水灌溉、农业水土资源合理利用和作物生长等方面，介绍了有关的力学问题和目前的研究进展．     

一种岩石损伤本构模型在地下强爆炸中的应用

为了描述地下爆炸波的传播,建立了一种考虑塑性硬化、剪胀和损伤软化效应的岩石本构模型,并应用于地下强爆炸自由场的数值计算,获得的速度和位移波形以及峰值速度衰减曲线等与国外地下试验测量数据和同类计算相比十分接近,从而验证了本构模型的有效性。     

矩形板结构损伤的分区域神经网络识别方法

通过引入LM优化算法，针对矩形薄板中对称结构的损伤识别问题，提 出了一种基于神经网络的分区域分步识别方法. 对于预测输出量比较多且对预测精度要求比 较高的问题，常会出现网络训练时收敛速度慢、网络预测精度低，并且当网络训练达到目标 误差时，输出的预测量中常有某个输出量的误差还很大的情况. 针对这些问题，利用选 取的组合输入参数，提出了基于神经网络的分区域识别方法. 通过对悬臂板结构的数值模拟 结果表明：提出的分区域识别方法对结构损伤的分区和预测是可行和有效的， 其预测精度要明显的高于只用单个网络的预测结果，并且预测子网络对损伤的位置和程度是 同步输出的，从而避免了传统分步识别理论中子网络过多的问题.     

ANALYSIS OF THE LOCALIZATION OF DAMAGE AND THE COMPLETE STRESS-STRAIN RELATION FOR MESOSCOPIC HETEROGENEOUS ROCK UNDER UNIAXIAL TENSILE LOADING

The mechanical behavior of rock under uniaxial tensile loading is different from that of rock under compressive loads. A micromechanics-based model was proposed for mesoscopic heterogeneous brittle rock undergoing irreversible changes of their microscopic structures due to microcrack growth. The complete stress-strain relation including linear elasticity, nonlinear hardening, rapid stress drop and strain softening was obtained. The influence of all microcracks with different sizes and orientations were introduced into the constitutive relation by using the probability density function describing the distribution of orientations and the probability density function describing the distribution of sizes. The influence of Weibull distribution describing the distribution of orientations and Rayleigh function describing the distribution of sizes on the constitutive relation were researched. Theoretical predictions have shown to be consistent with the experimental results.     

含纳米粒子溶液对单晶硅表面的冲蚀磨损损伤实验研究

利用高分辨透射电子显微镜和原子力显微镜观察了含纳米颗粒溶液冲蚀硅片表面损伤行为,考察了纳米颗粒碰撞单晶硅片所导致的微观物理损伤.结果表明:冲蚀30 s后,在高分辨透射电子显微镜下可见硅片表面呈现方向性损伤,并可观察到大量非均匀的晶格缺陷;当冲蚀10 min时,硅片表面出现微观划痕和凹坑,在划痕一端可见原子堆积,亚表面可观察到镶嵌晶粒的非晶损伤层;继续延长冲蚀时间将加剧其表面损伤.     

MICROMECHANICAL MODELLING OF STRAIN SOFTENING IN MICROCRACK-WEAKENED QUASI-BRITTLE MATERIALS

By using the concept of domain of microcrack growth(DMG),themicromechanisms of damage in quasi-brittle materials subjected to triaxial either tensileor compressive loading are investigated and the complete strew-strain relation includingfour stages is obtained from micromechanical analysis.The regime of pre-peaknonlinear hardening corresponds to the distributed damage,i.e.the stable propagationof microcracks.After the attainment of the ultimate strength of load-bearing capacity,some microcracks experience the second unstable growth and the distributed damage istransmitted to the localization of damage.These analyses improve our understanding ofthe hardening and softening behaviors of quasi-brittle materials.     

Dynamic compression-shear response of brittle materials with specimen recovery

A new configuration for compression-shear soft-recovery experiments is presented. This technique is used to investigate various failure mechanisms during dynamic multiaxial loading of an Al₂O₃/SiC nanocomposite and TiB₂. Velocity profiles of the target surface are measured with a variable sensitivity displacement interferometer, yielding normal and transverse velocity-time histories. A dynamic shear stress of approximately 280 MPa is obtained, in the Al₂O₃/SiC nanocomposite, for an imposed axial stress of about 3.45 GPa on a 540 m thick sample. This dynamic shear stress is well below the value predicted by elastic wave propagation theory. This could be the result of stress-induced damage and inelasticity in the bulk of the sample or inelasticity on the sample surface due to frictional sliding. To gain further insight into the possible failure mechanisms, an investigation of compression-shear recovery techniques, with simultaneous trapping of longitudinal and lateral release waves, is conducted.